Concentrate Formula:

Mix 1 part 30 SECONDS Outdoor Cleaner with 1 part water. For example: Mix 1 gallon of cleaner with 1 gallon of water.

Ready To Use Formula:

No mixing required. This product is ready to go.

Directions:

• Apply 30 SECONDS Outdoor Cleaner when the surface is DRY.
• Keep surface wet with the product according to the label. The saturation time will vary depending on the amount of build up, and the porosity of the surface.

For example:

Concrete, Masonry, Tile, Asphalt - these are very porous so they require the most saturation:

• Spray on DRY surface.
• Keep wet with the product for up to 15 minutes.
• Hose off thoroughly with water.

Wood - this is slightly porous so it requires more saturation than vinyl siding:

• Spray on DRY surface.
• Keep wet with the product for up to 5 minutes.
• Brush or sweep the surface with the grain (if necessary).
• Hose off thoroughly with water.

Metal, Cloth, Paint, Plastic, Fiberglass:

• Test any cloth material on a small inconspicuous area first to make sure it is colorfast material.
• Spray on DRY surface.
• Keep wet with the product for up to 3 minutes.
• Brush (if necessary) and rinse thoroughly with water, within 10 minutes.

In General:

• It's optional to brush the surface if necessary, to loosen stubborn build up.
• Re-application, prior to rinsing, may be necessary where heavy build up occurs.
• Rinse thoroughly with water, using a garden hose. The cleaning action stops when your surface dries.
• Do not let 30 SECONDS dry on glass. Give windows an extra rinse after cleaning to prevent any residue being left behind.
• After use, clean applicator thoroughly with water.
• Store in a cool, dry place.

Helpful Hints: 

• Always test on an inconspicuous area first, on surfaces that are susceptible to corrosion, dulling and bleaching. For example: fabric, color paving, high gloss paint and untreated metals.
• Wear protective clothing and footwear. 30 SECONDS Outdoor Cleaner will bleach out your clothes.
• Rinse from plants and metals within 10 minutes of application.
• Once you are familiar with how well 30 SECONDS Outdoor Cleaner works, it can be diluted up to 4 times more. Then you keep the surface wet, 4 times as long. Refer to the label directions for more information.

• Shake contents before use.
• Mix one part of 30 SECONDS Spray & Walk Away to five parts water (1:5 mix ratio). 1 gallon makes 6 gallons of Ready-To-Use product and treats 750-2250 sq. ft., depending on the growth and porosity of the surface. Use a backpack or pump up tank sprayer to apply.
• Spray surface to be treated when surface is DRY and rain is not predicted for 12 hours or longer.
• Thoroughly saturate surfaces to be treated. To maximize coverage, remove excessive organic growth or clumps where possible, prior to applying Spray & Walk Away. This will save you money and increase the effectiveness of the product.
• Once treated, the surface requires no pressure washing, scrubbing or rinsing. Just thoroughly WET the surface with the product and WALK AWAY.
• Treated surfaces will show signs of decay over the next few weeks and growth will erode away with the weather. Alternatively, leave treated surface for a few days after treatment, then brush off decaying growth with a stiff brush.
• After use, clean and flush applicator thoroughly with water.
• If you prefer immediate results, we recommend 30 SECONDS Outdoor Cleaner.For example:

For example:

Concrete, Masonry, Tile, Asphalt:

• Spray on DRY surface.
• Keep wet with the product for up to 15 minutes.
• Brush (if necessary)
• Hose off thoroughly with water.

Wood:

• Spray on DRY surface.
• Keep wet with the product for up to 5 minutes.
• Brush surface with the grain.
• Hose off thoroughly with spray nozzle.

Stained Wood:

• Stain can be removed during cleaning, leaving a blotchy appearance, which can be remedied by re-staining. (See Helpful Hints below)

Metal, Cloth, Paint, Plastic, Fiberglass:

• Spray on DRY surface.
• Keep wet with the product for up to 3 minutes.
• Brush (if necessary) and rinse thoroughly with water, within 10 minutes.
• Do not use on copper

Helpful Hints:

• Always test on an inconspicuous area first, on surfaces that are susceptible to corrosion, dulling and bleaching. For example: fabric, color paving, high gloss paint and untreated metals.
• Wear protective clothing and footwear to prevent bleaching to regular clothing.
• Rinse from plants and metals within 10 minutes of application.
• Refer to the label directions for more information.
• After use, clean applicator thoroughly with water.
• Store in a cool, dry place.